If like me you need to setup your rb750up as a switch, i have managed to bridge ports 1,2,3,4 so you can use port 1 as a poe power source and then use ports 2,3,4 to power your ubiquiti devices. Port 5 is only used for access to the router board with winbox etc. I have left the default dhcp on port 5 so you can access via 192.168.88.1 but port 5 is not bridged.
download the config Routerboard RB750UP switch config
just use winbox to connect to routerboard then drag the backup file to files in winbox, highlight and restore.
Sunday 28 October 2012
Sunday 17 June 2012
coova-chilli build on ubuntu
This is my install of coova-chilli on ubuntu 8.04 server
I already have a radius server with wireless orbit
so install ubuntu with no extras (ftp apache mysql) and setup the eth0 interface network
set up a user account as asked and password
once built
sudo apt-get update
sudo apt-get upgrade
apt-get ssh
log into ssh with host username and port (22) and password
sudo wget http://ap.coova.org/chilli/coova-chilli_1.0.12-1_i386.deb
sudo dpkg -i coova-chilli_1.0.12-1_i386.deb
sudo nano -w /etc/default/chilli
change
START_CHILLI=0
CONFFILE=”/etc/chilli.conf”
to
START_CHILLI=1
CONFFILE=”/etc/chilli.conf”
ctrl x – yes – enter
now at this point i have a chilli.conf already made with the lines
include /usr/local/etc/chilli/main.conf
include /usr/local/etc/chilli/hs.conf
include /usr/local/etc/chilli/local.conf
deleted
here is my chilli conf
________________________________________________________________________________
#
# Chilli Configuration
#
# To configure chilli, see /usr/local/etc/chilli/default
# and then create your own /usr/local/etc/chilli/config
# start / stop chilli with /chilli
#
# For help with coova-chilli,
# visit http://coova.org/wiki/index.php/CoovaChilli
#
# This file can either contain all your chilli configurations, or include
# other files, as shown per default below. The idea here is that main.conf
# contains your main configurations, hs.conf is for your configurations
# delivered by RADIUS (using the Administrative-User login), and local.conf
I already have a radius server with wireless orbit
so install ubuntu with no extras (ftp apache mysql) and setup the eth0 interface network
set up a user account as asked and password
once built
sudo apt-get update
sudo apt-get upgrade
apt-get ssh
log into ssh with host username and port (22) and password
sudo wget http://ap.coova.org/chilli/coova-chilli_1.0.12-1_i386.deb
sudo dpkg -i coova-chilli_1.0.12-1_i386.deb
sudo nano -w /etc/default/chilli
change
START_CHILLI=0
CONFFILE=”/etc/chilli.conf”
to
START_CHILLI=1
CONFFILE=”/etc/chilli.conf”
ctrl x – yes – enter
now at this point i have a chilli.conf already made with the lines
include /usr/local/etc/chilli/main.conf
include /usr/local/etc/chilli/hs.conf
include /usr/local/etc/chilli/local.conf
deleted
here is my chilli conf
________________________________________________________________________________
#
# Chilli Configuration
#
# To configure chilli, see /usr/local/etc/chilli/default
# and then create your own /usr/local/etc/chilli/config
# start / stop chilli with /chilli
#
# For help with coova-chilli,
# visit http://coova.org/wiki/index.php/CoovaChilli
#
# This file can either contain all your chilli configurations, or include
# other files, as shown per default below. The idea here is that main.conf
# contains your main configurations, hs.conf is for your configurations
# delivered by RADIUS (using the Administrative-User login), and local.conf
cmdsocket /usr/local/var/run/chilli.sock
pidfile /usr/local/var/run/chilli.pid
net 192.168.180.0/255.255.255.0
uamlisten 192.168.180.1
uamport 3990
dhcpif eth1
uamallowed 69.36.234.20,www.paypal.com,
www.wirelessorbit.com,paypal.112.207.net,www.paypalobjects.com,portal.wirelessorbit.com
uamanydns
pidfile /usr/local/var/run/chilli.pid
net 192.168.180.0/255.255.255.0
uamlisten 192.168.180.1
uamport 3990
dhcpif eth1
uamallowed 69.36.234.20,www.paypal.com,
www.wirelessorbit.com,paypal.112.207.net,www.paypalobjects.com,portal.wirelessorbit.com
uamanydns
domain lan
dns1 192.168.180.1
uamhomepage http://192.168.182.1:3990/www/coova.html
wisprlogin https://coova.org/app/uam/auth
wwwdir /etc/chilli/www
wwwbin /etc/chilli/wwwsh
locationname “HotSpot”
radiuslocationname HotSpot
radiuslocationid isocc=,cc=,ac=,network=Coova,
radiusserver1 69.36.234.20
radiusserver2 (leave blank for wireless orbit)
radiussecret *********
radiusauthport 1812
radiusacctport 1813
uamserver https://portal.wirelessorbit.com/portal/index.php?portal_id=**********,
radiusnasid nas01
dns1 192.168.180.1
uamhomepage http://192.168.182.1:3990/www/coova.html
wisprlogin https://coova.org/app/uam/auth
wwwdir /etc/chilli/www
wwwbin /etc/chilli/wwwsh
locationname “HotSpot”
radiuslocationname HotSpot
radiuslocationid isocc=,cc=,ac=,network=Coova,
radiusserver1 69.36.234.20
radiusserver2 (leave blank for wireless orbit)
radiussecret *********
radiusauthport 1812
radiusacctport 1813
uamserver https://portal.wirelessorbit.com/portal/index.php?portal_id=**********,
radiusnasid nas01
papalwaysok
uamsecret *********
uamsecret *********
ipup=/etc/chilli/up.sh
ipdown=/etc/chilli/down.sh
ipdown=/etc/chilli/down.sh
___________________________________________________________________________
before i do anything with my chilli.conf i start chilli
sudo /etc/init.d/chilli start
then stop it again
sudo /etc/init.d/chilli stop
this writes the defaults
then i transfer with a ssh file transer window
i use ssh secure shell but winscp will do
transfer into /home/username
then
sudo cp chilli.conf /etc/chilli.conf
finally
sudo nano /etc/rc.local
add the line
iptables -I POSTROUTING -t nat -o eth0 -j MASQUERADE
to turn on nat
ctrl +x answer y and enter
you might also want a second dns server for you wan eth0
i use opendns
so
sudo nano /etc/resolv.conf
nameservers 208.67.222.222
nameservers 208.67.220.220
ctrl +x answer y and enter
sudo reboot and if radius configured correctly you should have a coova redirect page
then your login page with your radius server
i also fiddle with the index.html in /etc/chilli/www to put a company logo and name for the small redirect page before it goes to the main login page
sudo /etc/init.d/chilli start
then stop it again
sudo /etc/init.d/chilli stop
this writes the defaults
then i transfer with a ssh file transer window
i use ssh secure shell but winscp will do
transfer into /home/username
then
sudo cp chilli.conf /etc/chilli.conf
finally
sudo nano /etc/rc.local
add the line
iptables -I POSTROUTING -t nat -o eth0 -j MASQUERADE
to turn on nat
ctrl +x answer y and enter
you might also want a second dns server for you wan eth0
i use opendns
so
sudo nano /etc/resolv.conf
nameservers 208.67.222.222
nameservers 208.67.220.220
ctrl +x answer y and enter
sudo reboot and if radius configured correctly you should have a coova redirect page
then your login page with your radius server
i also fiddle with the index.html in /etc/chilli/www to put a company logo and name for the small redirect page before it goes to the main login page
Freepbx PIAF Atcom AX-100P install
I decided to purchase an atcom ax-100p for my home pbx as it was only £20.00 on ebay.
I decided on using Pbx in a Flash or PIAF. I inserted the card before i built the PIAF system.
AFter installing PIAF i ran the suggested genzaptelconf command which recognised the card.
I decided on using Pbx in a Flash or PIAF. I inserted the card before i built the PIAF system.
AFter installing PIAF i ran the suggested genzaptelconf command which recognised the card.
I now went about configuring parameters for the card. Upon my first attempt i was able to get it working on incoming calls but not for outgoing it was coming up with stange results for the ztcfg -vvvv command saying i had 100 channels to configure so i new something was wrong.
So i decided to run the genzaptelconf command with options -s -d -v this then reconfigured the card but still it had an extra span in the zaptel.conf so i deleted that section and also the extra in zapata-channels.conf so there was only 1 span.
Rebooted made sure the zap channels DIDs was created in freepbx, and that i had a freephone number to dial using zap/go
and i was able to use my zap card.
So i decided to run the genzaptelconf command with options -s -d -v this then reconfigured the card but still it had an extra span in the zaptel.conf so i deleted that section and also the extra in zapata-channels.conf so there was only 1 span.
Rebooted made sure the zap channels DIDs was created in freepbx, and that i had a freephone number to dial using zap/go
and i was able to use my zap card.
Heres my working confs
Zaptel.conf
# Autogenerated by /usr/local/sbin/genzaptelconf — do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#
# Autogenerated by /usr/local/sbin/genzaptelconf — do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#
# It must be in the module loading order
# Span 1: WCFXO/0 “Wildcard X100P Board 1″ (MASTER)
fxsks=1
fxsks=1
# Global data
loadzone = uk
defaultzone = uk
defaultzone = uk
Zapata.conf
;
; Zapata telephony interface
;
; Configuration file
; Zapata telephony interface
;
; Configuration file
[trunkgroups]
[channels]
language=en
context=from-zaptel
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
;
; Whether or not to do distinctive ring detection on FXO lines
;
usedistinctiveringdetection=yes
cidsignalling=v23 ; Added for UK CLI detection
cidstart=polarity ; Added for UK CLI detection
;callerid=asreceived ; propagate the CID received from BT
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=800
rxgain=6.0
txgain=4.0
group=0
callgroup=1
pickupgroup=1
immediate=no
;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no
context=from-zaptel
signalling=fxs_ks
rxwink=300 ; Atlas seems to use long (250ms) winks
;
; Whether or not to do distinctive ring detection on FXO lines
;
usedistinctiveringdetection=yes
cidsignalling=v23 ; Added for UK CLI detection
cidstart=polarity ; Added for UK CLI detection
;callerid=asreceived ; propagate the CID received from BT
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=yes
echotraining=800
rxgain=6.0
txgain=4.0
group=0
callgroup=1
pickupgroup=1
immediate=no
;faxdetect=both
faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no
;Include genzaptelconf configs
#include zapata-channels.conf
#include zapata-channels.conf
;Include AMP configs
#include zapata_additional.conf
#include zapata_additional.conf
Zapata-channels.conf
; Autogenerated by /usr/local/sbin/genzaptelconf — do not hand edit
; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is intended
; to be #include-d by /etc/zapata.conf that will include the global settings
;
; Zaptel Channels Configurations (zapata.conf)
;
; This is not intended to be a complete zapata.conf. Rather, it is intended
; to be #include-d by /etc/zapata.conf that will include the global settings
;
; Span 1: WCFXO/0 “Wildcard X100P Board 1″ (MASTER)
;;; line=”1 WCFXO/0/0 FXSKS (In use)”
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 1
context=default
;;; line=”1 WCFXO/0/0 FXSKS (In use)”
signalling=fxs_ks
callerid=asreceived
group=0
context=from-zaptel
channel => 1
context=default
After this i decided to have a bit of fun
so i created a dialout rule so if i dial 1471 it then passes to BT to get the last caller id
1472 as a feture code on freepbx for call trace for voip numbers.
so i created a dialout rule so if i dial 1471 it then passes to BT to get the last caller id
1472 as a feture code on freepbx for call trace for voip numbers.
Subscribe to:
Posts (Atom)